设计描述：

文档包括:
说明书一份,37页,17000字左右.
工艺卡片一份.

CAD版本图纸12张:

车床套工艺及夹具设计

摘 要

工艺学是以研究机械加工工艺和夹具设计为主的一门学科，具有很强的实践性，要求在学习过程中应紧密联系生产实践，同时它又具有很强的综合性，
本次毕业设计的课题是车床套加工工艺规程的制定及后三道工序专用夹具设计，主要内容如下：
首先，对零件进行分析，主要是零件作用的分析和工艺分析，通过零件分析可以了解零件的基本情况，而工艺分析可以知道零件的加工表面和加工要求。根据零件图提出的加工要求，确定毛坯的制造形式和尺寸的确定。
第二步，进行基面的选择，确定加工过程中的粗基准和精基准。根据选好的基准，制订工艺路线，通常制订两种以上的工艺路线，通过工艺方案的比较与分析，再选择可以使零件的几何形状、尺寸精度及位置精度等技术要求得到合理的保证的一种工序。
第三步，根据已经选定的工序路线，确定每一工步的切削用量及基本工时，并选择合适的机床和刀具、量具。对于粗加工，还要校核机床功率。
最后，经过多方面的考虑，设计了后三道工序的专用夹具，即两套钻模和一套铣台阶面的铣床夹具。先提出设计问题，再选择定位基准，然后开始切削力、夹紧力的计算和定位误差的分析。然后把设计的过程整理为图纸，并编写说明书。
通过以上的概述，整个设计基本完成。
关键词：机械；车床套；加工工艺；夹具设计

LATHER SET'S TECHNOLOGY AND FIXTURE DESIGN

ABSTRACT

A specialized main specialized course that " mechanical manufacturing engineering is studied " is machinery , rely mainly on studying machining technology and jig to design technological discipline , have very strong practicality , require that should contact production practices closely in the learning process, at the same time it has comprehensive the very strong one,
The topic of this graduation design is the lather set establishment and empress that processes craft regulations three work preface appropriation tongs designs, the main contents is as follows:
First of all, analyze ， it is mainly analysis of the function of the part and craft analysis to the part , through part analyze can find out about basic situation of part, and craft analyze may know the processing surface of the part and is it require to process. The processing demand put forward according to the part picture, confirm the manufacture form of the blank and sureness of the size.
The second step, carry on the choice the base ， confirm thick datum and precise datum in the processing course. According to the datum chosen ， make the craft route , usually make the craft route of more than two kinds, with analyzing through the comparison of the craft scheme, and then choosing be able to make such specification requirements as the precision of geometry form , size of the part and precision of position ,etc. get a kind of process of the rational assurance s.
The third step, according to the already selected process route, confirm for every steps of cutting consumption and basic man-hour ， choose suitable lathe and cutter. To rough machining ， will check the power of the lathe .
End, pass by various of consideration, after designing three appropriation tongses of work prefaces, namely two sets of miller tongses that drill the mold and a set of Xian step noodles.Put forward the question of designing first ， and then choose to orient the datum , then the calculation that begins to cut strength , clamp strength and analysis of the localization error. Then put the design course in order as the drawing.
Through the summary of the above, design and finish basically entirely.

Keywords：machine， Lather set，Process the craft，The fixture design

目　录

前　言 1
第一章 零件的分析 2
1.1零件的作用 2
1.2零件的工艺分析 2
1.2.1 以Φ25H7为中心的一组加工表面 2
1.2.2 以尺寸90为中心的一组加工表面 2
第二章  工艺规程设计 3
2.1 确定毛坯的制造形式 3
2.2 基面的选择 3
2.2.1 粗基准的选择 3
2.2.2 精基准的选择 3
2.3加工方法的确定 3
2.4 制定工艺路线 4
2.4.1 加工工艺路线方案一 4
2.4.2  工艺路线方案二 5
2.4.3  工艺路线方案分析与比较 5
2.5 机械加工余量、工序尺寸及毛坯尺寸的确定 5
2.5.1  外圆的加工余量及公差 6
2.5.2  外圆标面沿轴线长度方向的加工余量及公差 6
2.5.3内孔的加工余量及公差 6
2.5.4铣削的加工余量及公差 7
2.6确立切削用量及基本工时 7
2.6.1  工序二 粗车Φ42、Φ45、Φ70外圆，切槽3 0.5，钻扩孔φ25H7 7
2.6.2  半精车Φ42、Φ45m6粗精铰孔Φ25H7，扩孔Φ31，倒角。 12
2.6.3  工序五 铣开裆尺寸5H9 16
2.6.4 工序六  钻孔φ7－φ13 18
2.6.5 工序七  铣尺寸29，保证尺寸59.5。 20
2.6.6 工序八   钻铰孔φ8H9、扩R5 21
2.6.7工序九 检查 24
2.6.8工序十 入库 24
第三章  夹具设计 24
3.1  钻孔φ7－φ13 24
3.1.1问题的提出 24
3.1.2夹具设计 24
3.2铣尺寸29，保证尺寸59.5 26
3.2.1问题的提出 26
3.2.3夹具设计 26
3.3 钻孔φ8－R10 27
3.3.1问题的提出 27
3.3.2夹具设计 27
结　论 29
谢  辞 30
参考文献 31
附　录 32