设计描述:
文档包括:
说明书一份,52页,21000字左右.
CAD版本图纸,共8张:
轴向柱塞泵设计
摘要
液压泵是向液压系统提供一定流量和压力的油液的动力元件,它是每个液压系统中不可缺少的核心元件,合理的选择液压泵对于降低液压系统的能耗、提高系统的效率、降低噪声、改善工作性能和保证系统的可靠工作都十分重要。
本次设计对轴向柱塞泵进行了分析,主要分析了轴向柱塞泵的分类,对其中的结构,如柱塞的结构型式、滑靴结构型式、配油盘结构型式等也进行了分析和设计,还包括它们的受力分析与计算。同时缸体的材料选用以及校核也很关键,本文对变量机构分类型式也进行了分析,最后利用Solidworks制图软件绘制零件图与组装成装配图,并进行干涉检验,无误后出图。本文对柱塞泵今后的发展也进行了展望。
关键词:轴向,柱塞泵,设计计算,Solidworks
DESIGN OF AXIAL PISTON PUMP
ABSTRACT
Hydraulic pump is the power components which can Provide a certain discharge and pressure of the oil for Hydraulic system. It is indispensable core components for each hydraulic system. It is very important to select a reasonable hydraulic pump, because it can effectively Reduce the energy consumption of the hydraulic system, improve system efficiency, reduce noise, improve performance and ensure reliable operation of the system.
This design analysis axial piston pump. It mainly analyzed the classification of axial piston pump, on which the structure, such as the structure type of the plunger, the structure type of slipper and oil pan structure type carried out analyzed and designed, including stress analysis and calculation of their too. At the same time, the selection of materials and checking the cylinder is also critical, the type of variable institutional classification was also analyzed in this paper, finally, Drawing parts drawing and installing Assembly body use the drawing software of solidworks, and drawing them after interference testing. The future development of piston was also discussed in this paper.
KEYWORDS: axial, piston pump, design and calculation, solidworks
目 录
摘要(中文) I
摘要(英文) II
1绪论 i
1.1引言 1
1.2轴向柱塞泵国内外研究现状与发展方向 1
2直轴式轴向柱塞泵工作原理与性能参数 3
2.1直轴式轴向柱塞泵工作原理 3
2.2直轴式轴向柱塞泵主要性能参数 4
2.2.1排量、流量、容积效率与结构参数 4
扭矩与机械效率 5
2.2.3功率与效率 6
3直轴式轴向柱塞泵运动学及流量品质分析 6
3.1柱塞运动学分析 6
3.1.1柱塞行程 S 7
3.1.2柱塞运动速度分析 V 7
3.1.3柱塞运动加速度a 7
3.2滑靴运动分析 8
3.3瞬时流量及脉动品质分析 9
3.3.1脉动频率 11
3.3.2脉动率 11
4柱塞泵主要部件的设计与受力分析 12
4.1柱塞设计与受力分析 12
4.1.1柱塞结构形式 12
4.1.2柱塞结构尺寸设计 12
4.1.3柱塞受力分析 13
4.2滑靴受力分析与设计 16
4.2.1滑靴受力分析 16
4.2.2滑靴设计 18
4.2.3滑靴结构型式与结构尺寸设计 19
4.3 配油盘受力分析与设计 22
4.3.1配油盘设计 22
4.3.2配油盘受力分析 23
4.3.3验算比压 、比功 26
4.4缸体设计 27
4.4.1 缸体的稳定性 27
4.4.2缸体主要结构尺寸的确定 27
4.5斜盘力矩分析 29
4.5.1柱塞液压力矩 30
4.5.2过渡区闭死液压力矩 30
4.5.3回程盘中心预压弹簧力矩 32
4.5.4滑靴偏转时的摩擦力矩 32
4.5.5柱塞惯性力矩 33
4.5.6柱塞与柱塞腔的摩擦力矩 33
4.5.7斜盘支承摩擦力矩 33
4.5.8斜盘与回程盘回转的转动惯性力矩 33
4.5.9斜盘自重力矩 33
5柱塞回程机构设计与变量机构 34
5.1柱塞回程机构设计 34
5.2 变量机构 35
6 SolidWorks三维制图 36
6.1 Solidworks简介 36
6.2 主要零件三维图与工程图 37
6.2.1 柱塞的三维图与工程图 37
6.2.2 滑靴的三维图与工程图 38
6.2.3 配油盘的三维图与工程图 39
6.2.4 缸体的三维图与工程图 40
6.3 轴向柱塞泵的装配体 41
结论 42
参考文献 43
致谢 44
|